-
Xtreme-Code™ Self-Adhesive High Temperature Pipe Markers - Vacuum
From $3.75 To $8.25Supplied in: Each -
Xtreme-Code™ Self-Adhesive High Temperature Pipe Markers - Waste
From $3.75 To $8.25Supplied in: Each -
Ultra-Mark® Self-Adhesive High Performance Pipe Markers - High Pressure Condensate
From $7.55 To $23.35Supplied in: Each -
Ultra-Mark® Self-Adhesive High Performance Pipe Markers - Hot Water
From $7.55 To $23.35Supplied in: Each -
Ultra-Mark® Self-Adhesive High Performance Pipe Markers - Hydrogen
From $7.55 To $23.35Supplied in: Each -
Ultra-Mark® Self-Adhesive High Performance Pipe Markers - Instrument Air
From $7.55 To $23.35Supplied in: Each
High Performance Pipe Markers
ANSI Pipe Labeling: Must-Do’s for Pipe Labeling Standards
Color code for quick recognition
Assign specific colors to different pipe contents, such as hazardous materials, fire protection systems or potable water. Consistent color coding simplifies identification and reduces the risk of accidents. Here’s the color-coding system recommended under ASME/ANSI A13.1
Fluid Service
Color Scheme |
|
---|---|
Fire Quenching Fluids | White on Red |
Toxic & Corrosive Fluids | Black on Orange |
Flammable & Oxidizing Fluids | Black on Yellow |
Combustible Fluids | White on Brown |
Potable, Colling, Boiler Feed, & Other Water | White on Green |
Compressed Air | White on Blue |
Defined by User | White on Purple |
Defined by User | Black on White |
Defined by User | White on Grey |
Defined by User | White on Black |
Match length and letter height to pipe diameter
Ensure that your pipe markers are appropriately sized for optimal visibility. Follow these guidelines by pipe size.
Fits Pipe Outer Diameter | 0.7" - 1.3" (18 - 33 mm) | 1.4" - 2.4" (34 - 61 mm) | 2.5" - 6.7" (62 - 170 mm) | 6.8" - 10" (171 - 254mm) | Over 10" (Over 254 mm) |
Length of Color Field | 8 in (203 mm) | 8" (203 mm) | 12" (305 mm) | 24" (610 mm) | 32" (813 mm) |
Letter Height | 0.5" (13 mm) | 0.7" (19 mm) | 1.3" (32 mm) | 2.5" (64 mm) | 3.5" (89 mm) |
Note: For pipes less than 0.7" diameter, a permanently legible tag is recommended
Place markers in key, high-visibility areas
Position pipe labels on pipes to achieve the best visibility. Install pipe labels below or above the horizontal centerline of the pipe when pipes are located above or below the normal line of vision, respectively. Consider placing pipe markers both near the ceiling and near the floor of your facility. In addition, mark pipes:
- Adjacent to all valves and flanges
- At both sides of floor or wall penetrations
- Adjacent to changes in directions
- At least every 50 feet on straight runs
valves and flanges.
sides of floor.
change in direction.
intervals on straight runs
- Text legend
-
- AIR (2)
- CHILLED WATER (2)
- CHILLED WATER RETURN (2)
- CHILLED WATER SUPPLY (2)
- CITY WATER (2)
- COLD WATER (2)
- COMPRESSED AIR (2)
- CONDENSATE (2)
- CONDENSATE RETURN (2)
- CONDENSER WATER RETURN (2)
- CONDENSER WATER SUPPLY (2)
- COOLING WATER (2)
- DEIONIZED WATER (2)
- DOMESTIC COLD WATER (2)
- DOMESTIC HOT WATER (2)
- DOMESTIC HOT WATER RETURN (2)
- DOMESTIC HOT WATER SUPPLY (2)
- DRAIN (2)
- FIRE PROTECTION WATER (2)
- FUEL OIL (2)
- GAS (2)
- HEATING RETURN (2)
- HEATING SUPPLY (2)
- HEATING WATER RETURN (2)
- HEATING WATER SUPPLY (2)
- HOT WATER (2)
- HOT WATER RETURN (2)
- HOT WATER SUPPLY (2)
- INSTRUMENT AIR (2)
- NATURAL GAS (2)
- NITROGEN (2)
- NON-POTABLE WATER (2)
- POTABLE WATER (2)
- PROPANE GAS (2)
- SANITARY SEWER (2)
- SPRINKLER FIRE (2)
- SPRINKLER WATER (2)
- STEAM (2)
- STEAM SUPPLY (2)
- STORM DRAIN (2)
- STORM WATER (2)
- VACUUM (2)
- VENT (2)
- View more
- View less
- Color
- Indoor or Outdoor Use
-
- Indoor Use (148)
- Outdoor Use (148)
- Material
-
- Plastic (31)
- Polyester (148)
- Height
-
- < 5.00 in (60)
- 5.00 - 9.99 in (16)
- >= 10.00 in (15)
- Width
-
- < 12.50 in (148)
- 12.50 - 24.99 in (129)
- >= 25.00 in (69)